Klanghelm DC1A Explained: Every Control, What Deep, Relaxed, Dual Mono and Negative Do, and a Settings Chart by Job
Klanghelm DC1A is the free compressor with two knobs: Input decides how hard it compresses, Output sets the level. What every control does (including the Mix control hidden in the meter display and the VU meter modes), what the Deep, Relaxed, Dual Mono and Negative switches change, a settings chart for vocals, bass, the drum bus, mix bus glue and parallel compression, setup steps, the mistakes, and how it compares with TDR Kotelnikov, MJUC jr and your stock compressor.
The short answer: Klanghelm DC1A is a free compressor with two knobs. There's no threshold, ratio, attack or release to set: Input decides how hard the signal hits the compressor (more Input, more compression), and Output sets the level coming out. Four switches change its character. Relaxed makes it gentler, with longer time constants and less saturation. Deep high-passes the detector so the low end doesn't make it pump. Dual Mono compresses the left and right channels separately. Negative switches to a curve with negative ratios, for obvious pumping. A Mix control in the meter display blends in the dry signal for parallel compression. For a vocal, switch Relaxed on and raise Input until the meter shows 2 to 4 dB of gain reduction on the loudest phrases; on a mix bus, add Deep and stop at 1 to 2 dB. Then match the level with Output. It's freeware from klanghelm.com, version 3.5.0 at the time of writing, with no account and no copy protection, in VST, VST3 and AAX on Windows 10 or later, plus AU on macOS 10.13 or later, native on Apple Silicon.
Compression is on every vocal, drum bus, and master on my releases (Sony, Universal, Ultra, Dim Mak, 50M+ streams), usually in small stages across two or three compressors rather than one working hard. DC1A is the two-knob free pick in the best compressor plugins, and this is the control-by-control version. It's free and there are no affiliate links on this page. I sell mastering chains with a glue compressor built in, disclosed at the end; none of them uses DC1A.
What DC1A is
Klanghelm calls DC1A "the little brother of the compression monster DC8C," its paid compressor. The developer, Tony Frenzel (credited with the code, the interface and the manual), says he took "a few of my favorite settings from DC8C" and made them work with two controls. Sound-wise it's "comparable to the PUNCH mode in DC8C," with two additions: negative ratios and stereo unlink. The pitch is "a compressor that just works," from "almost invisible, smooth leveling to heavy pumping with a nice crunchy saturation," and "punchy enough to treat drums with."
What to know before installing it:
- Free, direct download. Klanghelm's DC1A page has a Windows installer and a macOS installer, with no sign-up. Klanghelm's FAQ says it uses no copy protection on any of its plugins.
- DC1A3 is the current one. The download page lists version 3.5.0. Per the manual, DC1A3 doesn't replace DC1A2 in your old projects, so both can sit side by side, and the old installer is still on Klanghelm's site.
- Formats and systems. Klanghelm's FAQ lists Windows 10 or higher with a 64-bit VST, VST3 or AAX host (Pro Tools 11 or higher), and macOS 10.13 or higher with a 64-bit VST, VST3, AU or AAX host, on Intel Macs or Apple Silicon, "supported natively." So it loads as AU in Logic, AAX in Pro Tools, and VST3 in FL Studio, Ableton Live, Cubase and Studio One.
- It's calibrated to a level. The manual says DC1A3 is "internally calibrated to 0VU = -18dBFS." That matters more than it sounds, because with no threshold knob, how hot your track is decides how much a given Input setting compresses. More on that below.
Every control, explained
Control names and behavior are from Klanghelm's DC1A3 manual and product page. The knob ranges are read off Klanghelm's own screenshot.
| Control | What it does | How to use it |
|---|---|---|
| Input | Input gain in dB; the screenshot's scale runs from -20 to +20. With no threshold, this is the compression amount: more Input drives the signal harder into the compressor | Raise it on the loudest section until the meter shows your target reduction |
| Output | "Output / make-up gain" in dB, -20 to +20 on the screenshot | Bring the level back to match the bypassed signal |
| Mix | In the meter display ("MIX: 100%"). Drag or use the mouse wheel to change it, or click to type a value. 100% is compressed signal only, 0% is dry input only | 100% on a normal insert; lower it for parallel (New York style) compression |
| VU meter mode (OUT, GR) | Two buttons under the meter choose whether the needle shows the output level or the gain reduction. The meter is calibrated to the VU standard, 0 dBVU = -18 dBFS | GR while you set Input; OUT while you match the level |
| Bypass | Click the meter to bypass the plugin | Compare at matched level |
| Deep | "Enables a side-chain high pass filter to keep the low-end intact"; the product page says it reduces "pumping on bass heavy material" | On for bass, a kick-heavy drum bus and the mix bus |
| Relaxed | When lit, "gentler, less aggressive compression characteristics with longer time constants and less saturation." The product page adds that it gives peak and RMS compression | On for vocals, bass and bus glue; off for drums and attitude |
| Dual Mono | Disables the stereo link of the side chain, so the left and right channels are compressed separately (stereo tracks only) | Off on buses and anything centered |
| Negative | An "alternative compression curve with negative ratios at more extreme input settings," for "more aggressive, obvious, pumping compression" | An effect, not a fixer: loops, room sounds, a parallel crush |
What it doesn't have matters too. Klanghelm publishes no attack or release times, no ratio, and no frequency for the Deep filter, and the manual lists no external sidechain input. DC1A makes those decisions for you, and the switches move them. One more meter note: a VU needle is slow by design, built to show average level, so the GR reading is an average; the sharpest peaks are getting more reduction than the needle shows.
What the four switches do
| Switch | What changes | Use it on | Watch for |
|---|---|---|---|
| Deep | The detector stops hearing the lowest frequencies, so the low end triggers less compression. It filters the side chain, not the audio | Bass, kick-heavy drum buses, the mix bus | The low end coming forward, because it's now compressed less than the rest |
| Relaxed | Gentler and slower, with less saturation, and peak plus RMS detection | Vocal leveling, bass, mix bus glue | Too slow for spiky consonants or snare hits; switch it off for those |
| Dual Mono | Each side compresses on its own | A wide stereo source where one side spikes alone, like a hard-panned double recorded as a stereo track | The image leaning toward whichever side is compressing less; keep it off on buses |
| Negative | Past a point, a louder input comes out quieter, so the loudest hits drop below the softer ones | Pumping effects, a parallel crush on drums, room mics | Lost punch and a backwards feel on anything that should sound natural |
A normal ratio, like 4:1, lets the output rise 1 dB for every 4 dB the input goes over the threshold. A negative ratio flips that: past the point where it kicks in, more input means less output. Klanghelm says the negative ratios arrive "at more extreme input settings," so with Negative on you hear it most with Input pushed, and at gentle settings it changes little.
Input, and why the level you feed it matters
DC1A has no threshold, so the level going in decides where it starts working. Klanghelm calibrates it so 0 VU equals -18 dBFS, the same reference behind the -18 dB rule in what gain staging is. In practice:
- A hot track compresses hard at Input 0. If you need Input far below zero to get light compression, the track is coming in hot. Turn it down before DC1A (clip gain or a gain plugin) so the knob works in its middle range.
- A quiet track may barely compress. If Input is near the top and the needle hardly moves, raise the level going in instead.
- Moving Input can change the level as well as the compression. That's what Output is for. Every time you move Input, re-match with Output before you judge.
DC1A settings chart, by job
Klanghelm publishes no recommended settings, so these are general starting points for each job. Read gain reduction with the meter on GR, on the loudest section, and set the final amount by ear at matched level.
| Job | Relaxed | Deep | Dual Mono | Negative | Mix | Gain reduction | Watch for |
|---|---|---|---|---|---|---|---|
| Vocal leveling | On | Off, or on if plosives and low thumps grab it | Off | Off | 100% | 2 to 4 dB on loud phrases | Breaths and room coming up; de-ess after it |
| Vocal attitude (rap, aggressive pop) | Off | Off | Off | Off | 100% | 3 to 5 dB | Harsh consonants and crunch; switch Relaxed on if it bites |
| Bass (DI or synth bass) | On | On | Off | Off | 100% | 3 to 6 dB | Notes still jumping in level; a dull attack |
| Drum bus | Off | On if the kick drives everything | Off | Off | 100%, or 70 to 80% to keep the transients | 2 to 4 dB | The snare losing its crack; less Input or less Mix |
| Mix bus glue | On | On | Off | Off | 100% | 1 to 2 dB | Hearing it work; back off until you only notice it on bypass |
| Parallel crush on drums | Off | Off | Off | On | 20 to 40% | Heavy, needle near the end of the scale | The blend getting too loud; check it in mono |
| Pumping effect (loops, room mics) | Off | Off | Off | On | 100% | Heavy | The pump fighting the groove; you can't set the release, so lower Input |
Vocal leveling is where most people meet DC1A. How to compress vocals splits the job into a fast peak catcher and a slower leveler doing 2 to 3 dB, and DC1A on Relaxed is a quick, free way to fill the second slot. For the parallel rows, Mix replaces the usual send-and-return routing: lower it and the dry signal comes back in underneath.
How to set up DC1A
- Download it from klanghelm.com only. Free-plugin mirrors are how adware gets installed; the Camel Crusher story is the cautionary tale.
- Check the level going in. A track averaging well above -18 dBFS will be compressed hard before you touch anything; trim it first.
- Insert it where the job is: on a vocal after the cleanup EQ, on a bass or drum bus, or on the mix bus.
- Set the switches first, from the chart row for the job. Relaxed and Deep change how much the same Input setting compresses, so decide them before you set the amount.
- Switch the meter to GR, play the loudest section and raise Input until the needle shows your target.
- Switch the meter to OUT and match the level with Output. Click the meter to bypass and compare at the same loudness. Louder always sounds better at first.
- Lower Mix if you want parallel compression, then re-check the level.
- Listen in the mix, not solo. A vocal that sounds over-compressed alone often sits right against the beat, and the reverse.
Mistakes that make DC1A sound bad
- Treating Input as a volume knob. It's the compression amount. Output is the volume.
- Feeding it hot. If Input is at the bottom and it's still squashing, the problem is upstream.
- Negative on a lead vocal. The loudest words end up quieter than the soft ones. Keep it for effects.
- Dual Mono on a bus. The stereo image wanders every time one side gets louder.
- Relaxed off with lots of Input on the mix bus. That's the "heavy pumping with a nice crunchy saturation" end of the range, great on a drum loop and wrong for glue.
- Judging it louder. Re-match Output every time you move Input.
- Asking it for precision. No attack, release or sidechain input. When you need to set those, TDR Kotelnikov gives you every control, and ducking one sound under another is a job for the tools in the best sidechain plugins.
- Using it to fix the mix. If DC1A needs 8 dB on the mix bus to hold things together, the balance is the problem, and what dynamic range is explains what that much reduction gives away.
DC1A vs other free compressors
| Compressor | Price | What you set | Character | Best for |
|---|---|---|---|---|
| Klanghelm DC1A | Free | Input, Output, Mix, four switches | Character, from smooth leveling to crunchy pumping | Fast, musical compression on tracks and buses |
| TDR Kotelnikov | Free (the paid GE adds features) | Threshold, Ratio, Peak Crest, Attack, two Releases, Soft Knee, Low Freq Relax, Dry Mix | Clean, two detectors | Transparent mix bus and master glue |
| Klanghelm MJUC jr | Free | Compress, Make-Up, a Time Constants switch (Fast, Slow, Auto) | Variable-mu, with two gain stages and an interstage transformer simulation, per Klanghelm | Thick, slower glue on buses |
| Ableton Glue Compressor | Stock (Standard and Suite) | Full VCA-style controls | Console-style bus glue | Live users |
| Logic Compressor | Stock | Full controls, seven circuit models | From clean to FET and opto styles | Logic users |
| FL Studio Fruity Compressor, Fruity Limiter (COMP mode) | Stock | Full controls | Clean | FL users |
| Pro Tools Dyn3 Compressor/Limiter | Stock | Full controls | Clean | Pro Tools users |
MJUC jr is version 1.5.0 on Klanghelm's site at the time of writing, freeware like DC1A, and Klanghelm says its three-position switch sets the attack and release along with the timing that shapes its saturation. The difference that matters between DC1A and Kotelnikov is decisions versus control: Kotelnikov lets you set every timing and stays out of the way, and DC1A makes the timing choices for you and adds a little character. Your stock compressor can do anything DC1A does with more knobs; what DC1A buys you is speed. The rest of the free kit is in the best free plugins for music production.
Where I land (and the disclosure)
DC1A earns its place in every free plugin folder: two knobs, four switches, and a sound that goes from barely there to wrecked without menus. Set the switches for the job, use Input as the amount, and match the level with Output before you decide anything.
Its whole idea is that compression can be one decision. My mastering chains apply that idea to the master. The Ultimate Master Chain for Ableton is the Ableton chain I open on every release, built entirely from Live's stock devices: EQ Eight for the lo-cut, then Glue Compressor, then EQ Eight for mid/side clean-up, Channel EQs for the lows and the mids, EQ Eight for air, Utility for mono and width, and Limiter. Its 8 macros are LO-CUT, LOWS, MIDS, AIR, GLUE, MONO-MKR, WIDENER and LIMITER, and GLUE is the one-knob decision: it "compresses everything into one cohesive record," with the signal flow and gain staging already decided around it. Live 11 and Live 12 versions are both in the download, for Standard or Suite; Live 10 and older can't open it. On Logic, the Logic stock chain does the same job with Logic's own Compressor, and the Ultimate Master Chain Bundle has all five chains for $89, including the Ozone build for any DAW. None of them uses DC1A; the Ableton chain's glue stage is Glue Compressor. I'm biased; DC1A on your mix bus at 1 to 2 dB teaches the same move for free.
One knob for glue, already set
THE ULTIMATE MASTER CHAIN FOR ABLETON
My Ableton mastering chain as one rack: stock devices only, with Glue Compressor as the glue stage and 8 macros (LO-CUT, LOWS, MIDS, AIR, GLUE, MONO-MKR, WIDENER, LIMITER). Live 11 and Live 12 versions both included, Standard or Suite. $29, lifetime access.
Get the Ableton ChainQuick answers
Is Klanghelm DC1A free? Yes. Klanghelm calls it freeware: direct Windows and macOS installers from klanghelm.com, no account and no copy protection. The current version is DC1A3 (3.5.0 at the time of writing), in VST, VST3, AU and AAX, native on Apple Silicon.
What does Relaxed do on DC1A? It makes the compression gentler and less aggressive, with longer time constants and less saturation, and Klanghelm's page says it gives peak and RMS compression. Use it for vocal leveling, bass and bus glue; switch it off for drums and attitude.
What does Deep do on DC1A? It puts a high-pass filter on the side chain, so low frequencies trigger less compression. That keeps the low end intact and stops a kick or bassline pumping the whole signal.
What are good DC1A settings for vocals? Relaxed on, Deep off, Dual Mono and Negative off, Mix at 100%, Input raised until the GR meter shows 2 to 4 dB on the loudest phrases, then Output matched to the bypassed level. De-ess after it.
Does DC1A work in FL Studio, Logic and Pro Tools? Yes. It loads as VST3 in FL Studio, Ableton Live, Cubase and Studio One, AU in Logic and AAX in Pro Tools (11 or higher), on Windows 10 or later and macOS 10.13 or later.
Written by
CHARLIE CROWN
Founder of Born Creative Audio. Independent artist and engineer: 50M+ streams, 100% owned, never signed a record deal. Also founder of Born Creative Records. Work-for-hire remixes for Sony, Ultra, and Dim Mak. FabFilter featured artist; endorsed by iZotope, Sonarworks, and McDSP. Everything on this site comes from running a real independent music business, not theory.
Stay in the loop
KEEP READING
Production insights, release breakdowns, and independent artist strategies — straight to your inbox.